Skip to main content

Building Automation Products for UAE Commercial Properties

The field devices, protocol gateways and control modules that sit beneath a building management strategy, specified for offices, retail, hospitality and mixed-use buildings in Abu Dhabi and Al Ain, and on a project basis in Dubai.

MDT KNX Analog I/O 2-channel, flush mounted, 0 - 10 V, switchable In-/Output — KNX Analog Inputs & OutputsMDT DALI Control 2 x 64 Gateway, 4 SU MDRC — DALI InterfaceMDT Glass Push Button II Lite 2-fold, RGBW, neutral, Black — KNX KeypadFaradite COUPLER KNX — AV Installation AccessoryTense Frame for square 45 mm inserts, 6 mm, Alu 1F — Socket FrameIntesis AC Cloud Control for Fujitsu RAC and VRF systems - 1 unit — HVAC Gateway

📞 Call +971 50 852 9609   💬 WhatsApp   Request a Quotation

By Quicknet Engineering Team, Quicknet Computers · Reviewed by Jenson Cleetus · Last reviewed: 25 September 2026
The Hardware Layer

The Devices Beneath the Building Management System

A building management system is only as good as the equipment feeding it. The head-end software, dashboards and alarms depend on field devices that actually switch lighting circuits, drive blinds, read occupancy and energy, and on gateways that let air conditioning units, chillers and meters exchange data with the control network. This page covers that hardware layer.

KNX forms the backbone of many commercial fit-outs because it is an open standard, ISO/IEC 14543-3, supported by a wide range of manufacturers. MDT actuators and sensors handle switching, dimming, shading, heating valves, binary inputs and energy metering, while Faradite and Tense accessories complete the wiring and wall-plate side of the installation. Together they give contractors a consistent, documented hardware set across every floor.

Integration is where most commercial projects succeed or stall. Intesis gateways connect split and VRF air conditioning to KNX, BACnet and Modbus, and bridge DALI lighting and M-Bus meters into the same logic. FutureNow modules add flexible I/O and shading control, and the Tyba Turn 2 adds a rotary room controller. If you need the full strategy, including the BMS head-end, points schedule and operator interface, our building management system service page explains that scope.

Specification Advice

Specifying the Field Layer for a Commercial Building

Build the points schedule first

List every circuit, blind motor, AC unit, meter and sensor the building needs to control or monitor, with the protocol each one uses. That schedule drives actuator channel counts, gateway selection and panel space, and it becomes the reference document for commissioning and future maintenance.

Choose the HVAC integration route

Split and VRF systems usually connect through a manufacturer-specific interface, while central plant often exposes BACnet or Modbus. Intesis offers gateways for both cases. Confirm the AC brand, model series and the number of indoor units per gateway before ordering, as these determine the correct part.

Decide where DALI fits

DALI gives addressable control of individual luminaires and is common in offices and retail. A KNX to DALI interface lets lighting scenes, occupancy and daylight logic sit on the same KNX network as blinds and HVAC, rather than running as a separate island with its own controls.

Meter what you want to manage

KNX energy meters and M-Bus gateways bring consumption data into the control system, so lighting and HVAC schedules can be reviewed against actual use. Metering is easiest to install at the distribution board during fit-out and much harder to retrofit later.

Allow spare capacity

Tenancies change, meeting rooms are split and floors are re-planned. Leaving spare actuator channels, bus power supply headroom and panel space makes future changes a programming task rather than an electrical project, which keeps disruption to occupants to a minimum.

Keep the network separate and managed

IP gateways, controllers and cameras should sit on a managed, segmented network with documented addressing. This protects building systems from office IT traffic, simplifies fault finding and supports secure remote access for maintenance teams. It also keeps building data under the owner's control.

Browse the Catalogue

Commercial Building Automation Ranges

The categories below make up the hardware layer of a commercial automation system, from KNX field devices and wall controls to protocol gateways, I/O modules, networking and surveillance.

MDT KNX Actuators in the UAE — MDT KNX Analog I/O 2-channel, flush mounted, 0 - 10 V, switchable In-/Output

MDT KNX Actuators in the UAE

82 products · MDT

DIN-rail and flush-mounted MDT KNX actuators for switching, dimming, LED control, shading, heating valves, binary inputs and energy metering, engineered into distribution boards by Quicknet for residential and commercial projects across the UAE.

View the range →
MDT KNX Sensors and System Devices in the UAE — MDT DALI Control 2 x 64 Gateway, 4 SU MDRC

MDT KNX Sensors and System Devices in the UAE

73 products · MDT

MDT presence and motion detectors, climate, weather and leakage sensors, together with the bus power supplies, IP interfaces, line couplers and DALI, Modbus and air-conditioning gateways that form the backbone of a KNX installation.

View the range →
MDT KNX Push Buttons and Touch Panels in the UAE — MDT Glass Push Button II Lite 2-fold, RGBW, neutral, Black

MDT KNX Push Buttons and Touch Panels in the UAE

219 products · MDT

Glass and plastic KNX push buttons, colour-display room controllers and wall-mounted touch panels from MDT, specified, programmed in ETS and installed by Quicknet for villas, offices and hospitality projects across Abu Dhabi and Al Ain, with Dubai and other emirates handled on a project basis from our Abu Dhabi team.

View the range →
Tense KNX Keypads and Touch Screens in the UAE — Tense ENGR_M1

Tense KNX Keypads and Touch Screens in the UAE

255 products · Tense

Tense KNX push buttons and touch panels in forged, brushed, glass, Corian and natural stone finishes, for villas and residences where the switch is part of the interior design. We supply, install, programme and support them across Abu Dhabi and Al Ain, with Dubai and other emirates handled on a project basis from our Abu Dhabi team.

View the range →
Faradite KNX Keypads, Sockets and Sensors in the UAE — Faradite COUPLER KNX

Faradite KNX Keypads, Sockets and Sensors in the UAE

39 products · Faradite

Faradite TAP-5 KNX keypads in Alpha and ORE finishes, matching ORE 13A switched sockets and the compact Motion Sensor 360 range, for residences that want discreet sensing and solid-metal controls. We supply, install, programme and support them across Abu Dhabi and Al Ain, with Dubai and other emirates handled on a project basis from our Abu Dhabi team.

View the range →
Tense Socket Frames and Trimless Back Boxes in the UAE — Tense Frame for square 45 mm inserts, 6 mm, Alu 1F

Tense Socket Frames and Trimless Back Boxes in the UAE

200 products · Tense

Tense socket frames for square 45 mm and 55 mm inserts, plus trimless installation boxes that set KNX keypads and sockets flush with the wall. We supply and install them across Abu Dhabi and Al Ain, and in Dubai and other emirates on a project basis from our Abu Dhabi team, as part of complete KNX and wiring-device packages.

View the range →
Intesis AC and VRF Gateways for BMS — Intesis AC Cloud Control for Fujitsu RAC and VRF systems - 1 unit

Intesis AC and VRF Gateways for BMS and Smart-Home Integration in the UAE

55 products · Intesis

Interfaces that let split, ducted and VRF air conditioning speak BACnet, Modbus RTU, WiFi or cloud control, so every indoor unit can be scheduled, monitored and optimised from one building or home system.

View the range →
Intesis KNX, BACnet and Modbus Protocol Gateways in the UAE — Intesis BACnet IP & MS/TP Client or Modbus TCP & RTU Master

Intesis KNX, BACnet and Modbus Protocol Gateways in the UAE

66 products · Intesis

Protocol translation hardware that joins KNX, BACnet, Modbus, LonWorks, DALI-2, M-Bus, OCPP and VRF air conditioning into one coherent building or villa control system.

View the range →
Building Control I/O Modules: FutureNow and Tyba in the UAE — FutureNow 12+1 Channel Relay Module with Analog Inputs

Building Control I/O Modules: FutureNow and Tyba in the UAE

47 products · FutureNow, Tyba

FutureNow Ethernet and FN485 DIN-rail relay, dimmer, shading, thermostat and input modules, and the Tyba Turn 2 rotary room controller with its bus connectors, integrated by Quicknet into Control4, KNX and other control platforms across the UAE.

View the range →
Araknis Networking and WattBox IP Power Control in the UAE — Araknis Araknis 420 Series PoE+ Network Switch - 16 or 24 Port

Araknis Networking and WattBox IP Power Control in the UAE

66 products · Araknis, Pakedge, Planet, WattBox

Managed switches, VPN routers, Wi-Fi 6 and Wi-Fi 7 access points and remotely manageable power for the network backbone behind premium smart homes, home cinemas and offices.

View the range →
Luma Surveillance IP Cameras and NVRs in the UAE — Luma Luma Bridge

Luma Surveillance IP Cameras and NVRs in the UAE

55 products · Luma

IP bullet, dome and turret cameras from 2MP to 8MP, with PoE network video recorders, designed to sit neatly inside a smart-home or small-business security system.

View the range →
Need the Full System?

Products Here, Strategy on the BMS Page

This page: the hardware layer

Actuators, sensors, meters, gateways, I/O modules and networking, selected and supplied to match a points schedule.

BMS service: the strategy

Head-end software, graphics, alarms, trends and integration with fire, security and plant, covered on our building management system page.

Both: one accountable team

We can supply and commission the field layer for another integrator, or deliver hardware and BMS together under one scope.

Service Areas: Abu Dhabi and Al Ain

Quicknet supplies, installs, programmes and supports these products from its Mussafah head office and its branches in Abu Dhabi and Al Ain, and takes on projects in Dubai and other emirates on a project basis (Quicknet has no office there). Site surveys, installation and after-sales support cover Abu Dhabi city and its island and suburban communities (including Saadiyat, Yas, Al Reem, Khalifa City and Mussafah), and Al Ain. Dubai villa communities and commercial buildings are quoted on a project basis by our Abu Dhabi team.

Local pages: Building management systems in Abu Dhabi · Building management systems in Dubai · Building management systems in Al Ain

Need a Specification or Quotation?

Send us your drawings, room list or model numbers. Our engineers confirm compatibility, prepare a written, itemised quotation and handle supply, installation, programming and after-sales support in Abu Dhabi and Al Ain, and on a project basis elsewhere in the UAE.

📞 Call +971 50 852 9609   💬 WhatsApp   Request a Quotation
FAQ

Building Automation Products for UAE Commercial Properties — Frequently Asked Questions

What is the difference between building automation products and a BMS?

A building management system is the overall strategy and supervisory layer: the head-end software, graphics, alarms, trends and operator workflow. Building automation products are the hardware that makes it work on the ground, such as actuators, sensors, meters and gateways. This page covers that hardware. Our building management system service page covers the design and integration of the complete BMS.

Can KNX connect to an existing BACnet or Modbus BMS?

Yes. Intesis KNX to BACnet and KNX to Modbus gateways expose KNX group objects as points the existing BMS can read and write. That lets lighting, shading and room controls installed on KNX be supervised from the building's current head-end. The mapping has to be agreed with the BMS integrator and documented, which we handle as part of commissioning.

Which air conditioning systems can be integrated?

Intesis produces interfaces for many major split and VRF manufacturers, as well as generic BACnet and Modbus gateways for central plant. Compatibility depends on the specific model series and the number of indoor units, so we confirm each unit's details before selecting a gateway. Where no direct interface exists, an IR-based or dry-contact approach may still be possible.

Is KNX suitable for large commercial buildings?

KNX scales through lines and areas connected by couplers, and IP routers can link floors or buildings over the network. It is widely used in offices, hotels and public buildings. For very large sites, KNX usually handles room and floor control while a BMS supervises across the whole estate, with gateways linking the two.

Can building automation reduce energy use?

It can, when it is designed and operated well. Occupancy-based lighting, daylight dimming, AC setbacks in unoccupied rooms and schedule control all cut waste, and metering shows where energy is actually used. We do not quote a fixed saving figure because results depend on the building, its use and how the controls are tuned after occupation.

Do you maintain commercial automation systems after handover?

Yes. We provide annual maintenance contracts covering preventive checks, firmware updates, programming changes for tenancy or layout changes, and priority response from our branches in Mussafah, Abu Dhabi and Al Ain. Keeping an up-to-date project file and points schedule is part of the service, so any engineer can pick up the system later.

Building Management Systems (BMS)

Our full BMS service: strategy, head-end integration, points schedules and operator interfaces.

IoT Smart Building Solutions

Connected sensors, analytics and smart building platforms for commercial properties.

KNX Automation Services

How we design, install and programme KNX systems for commercial and residential projects.

Smart Lighting

Lighting control design, from scenes and schedules to occupancy and daylight response.

Structured Cabling

The copper and fibre infrastructure that building systems and networks rely on.

Smart Office Automation

Applying building automation hardware to offices, meeting rooms and commercial fit-outs.